Affiliate disclosure: As an Amazon Associate, HomeNode earns from qualifying purchases at no additional cost to you.
Short answer: Start with Synology’s web finder or the Synology Assistant utility, running on a computer that is on the same subnet as the NAS. If neither one sees it, find the NAS address in your router’s DHCP client list and open DSM directly by IP. When a DiskStation seems to be missing, it is usually online and hidden by guest Wi-Fi, a VLAN or the Windows Network view, which is unreliable.
This guide covers Synology hardware only and goes with our general guide to fixing a NAS that is not appearing on the network. It covers three situations: the setup wizard never finds the box, a shared drive disappears from File Explorer, or the finder reports that no Synology device was found. Try the steps in order.
Start with Synology’s own discovery tools
Open find.synology.com in a browser on the same network as the NAS. The site searches your local subnet and links you to DSM or the setup wizard. Turn off any VPN client first.
Synology Assistant is the desktop version, downloadable from your model’s page on Synology’s support site. It lists each NAS it finds with the IP and MAC address. Allow it through your firewall when prompted, because a blocked Assistant can show an empty list.
Both tools rely on discovery traffic that stays inside one subnet. A laptop on guest Wi-Fi, another VLAN or a VPN sees nothing, even when the NAS works normally.
| Discovery method | What it needs | When it fails | Best for |
|---|---|---|---|
| Synology web finder | Browser on the same subnet, no VPN | Different subnet or active VPN | First-time setup |
| Synology Assistant | Installed utility, firewall permission, same subnet | Firewall blocks it, guest Wi-Fi or VLAN separation | Seeing IP and MAC at a glance |
| Router DHCP list, then DSM by IP | Router admin access, NAS using DHCP | NAS set to a static IP outside your range | When discovery tools come up empty |
| Windows File Explorer Network view | Network discovery on, private network profile | Public profile, discovery services stopped | Casual browsing only |
| macOS Connect to Server | NAS address, SMB enabled in DSM | Wrong address or SMB turned off | Mac users mounting shares |
| QuickConnect | Internet access, a QuickConnect ID | Used to find a NAS on the LAN | Remote access away from home |
Find the IP in your router and open DSM directly
Log in to your router and open its DHCP client list, sometimes called attached devices. Look for the NAS hostname, or match the MAC address on the NAS label.
Synology documents 5000 as the default DSM port for HTTP and 5001 for HTTPS. Unless you changed it, browse to http:// followed by the IP and :5000. If DSM loads, the NAS is fine and only discovery is failing.
Give it a DHCP reservation
A NAS that picks up a new address after a router reboot breaks every mapped drive pointing at the old one. Reserve its current IP against its MAC address in the router. That also avoids a static DSM address that later clashes with another device.
Check the LEDs, cable and switch port
Synology units have a status LED and LAN LEDs that show whether DSM has booted and whether there is a link. Meanings vary by model, so check the LED table in your model’s Hardware Installation Guide.
A dark LAN light means no physical link. Swap in a known-good cable, try another router or switch port, and confirm the port’s own link light comes on. A spare unmanaged switch quickly shows whether a router port is at fault, and our roundup of network switches for a home lab compares more options.
Best for: Readers who want spare wired ports to test a NAS link without relying on a suspect router port.
- Strength: It has eight Gigabit Ethernet ports and plug-and-play setup that needs no software or configuration.
- Trade-off: It is an unmanaged switch, so it has no settings for dividing or monitoring traffic.

- 𝐆𝐢𝐠𝐚𝐛𝐢𝐭 𝐒𝐩𝐞𝐞𝐝𝐬 Enjoy ultra-fast data transfer rates with 8 Gigabit Ethernet ports, perfect for high-band…
- 𝐏𝐥𝐮𝐠-𝐚𝐧𝐝-𝐏𝐥𝐚𝐲 Setup is a breeze with no software or configuration needed, making it ideal for quick and ha…
- 𝐐𝐮𝐢𝐞𝐭 𝐎𝐩𝐞𝐫𝐚𝐭𝐢𝐨𝐧 Fanless design ensures silent operation, making it perfect for noise-sensitive environm…
Isolation, File Explorer and Finder: when the NAS only looks missing
Guest Wi-Fi, VLANs and client isolation
Guest networks keep visitors away from your devices, and the NAS is one of them. Some routers and mesh systems also isolate wireless clients from wired ones on the main network. Join the main network or plug in, and turn isolation off.
With VLANs, the NAS and your computer may sit on different subnets. Discovery stops at that boundary, but connections by IP work once firewall rules allow them.
Windows File Explorer
The Network view hides devices on a Public network profile and depends on discovery services that are not always running. DSM has a WS-Discovery option in its SMB settings, and Synology’s knowledge base shows where it sits in your DSM version.
Skip browsing instead. Choose Map network drive and enter two backslashes, the NAS IP, a backslash and the share name.
macOS Connect to Server
In Finder, choose Go, then Connect to Server, and enter smb:// followed by the NAS IP. Click the plus button to save it, since the sidebar drops network devices much as Windows does.
QuickConnect is not a LAN finder
QuickConnect is Synology’s relay for reaching DSM from outside your home. If it works but local access fails, the fault is in your local network path. For shares that open but crawl, see our slow NAS transfer troubleshooting guide.
Last resort, trade-offs and who should plan differently
If the LEDs show DSM running and the cable is fine but nothing answers, a wrong static IP or gateway is the likely cause. Synology’s knowledge base describes a RESET-button procedure that returns network settings to DHCP and resets the admin password without erasing data on the drives. A different button hold starts a more extensive reset, so follow Synology’s article for your model exactly.
If you run several subnets, plan to reach the NAS by IP from the start. A model with two network ports also gives you a second link to test, and our Synology NAS buyer’s guide compares the current lineup.
Best for: Households that want a compact media and photo server on a single wired connection.
- Strength: Its Intel CPU supports hardware transcoding for streaming 4K movies, shows and photos.
- Trade-off: It is a two-bay diskless unit, so it holds fewer drives than four-bay models.

- Your Personal Streaming Server – Build your own Netflix-style media library and stream 4K movies, shows and photos to…
- Create Your Own Cloud – Store your entire photo, video and music collection; access from anywhere with fast 282 MB/s…
- Creator-Grade Backup Solution – Protect your irreplaceable content with automated backups to cloud services, external…
Best for: Owners who want two network links and room to expand storage later.
- Strength: Its dual 2.5GbE ports offer faster network speeds and improved redundancy.
- Trade-off: The listing states it is only compatible with Synology branded drives.

- Dependable Performance – Up to 522/565 MB/s sequential read/write throughput for stable data transfers. Only compatib…
- Fast and Flexible Networking – Dual 2.5GbE ports offer fast network speeds and improved redundancy
- Versatile Network Storage – Includes file and photo management, data protection, virtualization, and surveillance fea…
Practical recommendation
Work through these steps in order and stop once the NAS responds:
- Synology’s web finder or Synology Assistant, on the same subnet.
- Your router’s DHCP list, then DSM by IP.
- The LEDs against your model’s hardware guide, then cable and port.
- Guest Wi-Fi, client isolation and VLAN settings.
- Shares mapped by IP in Windows or macOS.
- Synology’s documented network reset, exactly as written.
Once the NAS answers, reserve its address and map your shares by IP. Those two changes prevent most repeat problems.
Frequently asked questions
Why can’t Synology Assistant find a Synology NAS?
Synology Assistant only searches your local subnet. Guest Wi-Fi, VLANs, VPNs or a firewall can all hide the NAS from it. Check your router’s DHCP list and open DSM by IP instead.
How do you find a Synology NAS IP address?
Look in your router’s DHCP client list and match the hostname or MAC address. Synology Assistant also shows the IP when it can see the NAS.
Why does a Synology NAS not show in Windows Network?
The File Explorer Network view depends on discovery services and a private network profile, and it often fails to show devices. Map the share by IP instead.
Does resetting Synology network settings delete data?
According to Synology’s knowledge base, the network reset restores the network settings and the admin password without erasing data on the drives. Follow Synology’s article exactly, because a different button hold starts a more extensive reset.
How these picks were chosen: HomeNode compares products using manufacturer specifications, current Amazon listing details and published owner feedback. Products are not tested in-house, and listings change often, so confirm current specifications on the product page before buying.
Affiliate disclosure: As an Amazon Associate, HomeNode earns from qualifying purchases at no additional cost to you.
General information only, not professional advice. Details can change or contain errors, so check with the manufacturer or an official source before you rely on them. Use of this site is subject to our Disclaimer and Terms of Service.

